Detaljer på forslag

Vejmaterialer – Overfladebehandling – Prøvningsmetoder – Del 3: Bestemmelse af bindemidlers vedhæftningsevne til tilslaget ved hjælp af Vialit-pladeslagprøvning
Forslagstitel på sprog (en): Surface dressing – Test methods – Part 3: Determination of binder aggregate adhesivity by the Vialit plate shock test method
Nummer:DSF/prEN 12272-3
Type:Forslag
Kilde:CEN
Udvalg:S-347
Udvalgsnavn:Vejmaterialer og vejbygning
Forslag udgivet:18. jul 2024
Kommentarfrist:17. sep 2024
Antal kommentarer:0
Læs forslag
Committee Home Page
Tip en kollega
Beskrivelse af forslaget:This document specifies, for anhydrous bituminous binder (cut-back and fluxed bituminous binders), the measurement of the binder aggregate adhesivity and the influence of adhesion agents or interfacial dopes and adhesion characteristics as an aid to design binder aggregate systems for surface dressing. This document specifies methods of measurement of: - the mechanical adhesion of the binder to the surface of the aggregate; - the active adhesivity of the binder to the chippings; - the improvement of the mechanical adhesion and active adhesivity by adding an adhesion agent either into the mass of the binder or by spraying the interface between binder and chippings; - the wetting temperature of the binder to the aggregate; - the variation of adhesivity below the fragility temperature. The wetting capacity of the binder affects the adhesivity properties. With the presence of water, the wetting capacity of bitumen emulsion is naturally high. Even if mechanical adhesion and active adhesivity test methods are mainly dedicated to anhydrous bituminous binders (cut-back and fluxed bituminous binders), these measurements can also be practiced with bitumen emulsion with a personalized interpretation of the results that depends on the design of the binder aggregate system. For bitumen emulsion, the adhesivity is conventionally measured through the water immersion test (EN 13614). This test method is applicable for: - bituminous binders used for surface dressings (e.g. conventional or polymer modified binders; mainly anhydrous bituminous binders such as cut-back and fluxed bituminous binders and bitumen emulsions); - all the following aggregates sizes that can be used for surface dressings: - set 1: 2/5 mm, 5/8 mm, 8/11 mm and 11/16 mm; and - set 2: 2/4 mm, 2/6 mm, 4/6 mm, 4/8 mm, 6/10 mm, 6/12 mm and 10/14 mm. It is not intended that this method be used on site for quality control. NOTE – Further information concerning the purpose of the test can be found in Annex D. WARNING – The use of this document can involve hazardous operations. This document does not purport to address all of the safety problems associated with its use. It is the responsibility of the user of this document to establish appropriate safety practices and determine the applicability of regulatory limitations prior to use.

Du kan kommentere på alle dele af dette dokument. Forslag vises i ét af to formater:

PDF-version
HTML-version

Hvis du ser indholdsfortegnelsen i venstre side, er det HTML-formatet. For at kommentere skal du åbne de enkelte afsnit ved at klikke på afsnittet i indholdsfortegnelsen.

Hvis du i stedet bliver bedt om at downloade et dokument, er det PDF-formatet. Du skal åbne dokumentet i et separat vindue og derefter kommentere ved at angive afsnitsnummer eller -tekst i "Sektion". Der er mere vejledning, når du har klikket på "Læs forslag".

For at afsende kommentar til Dansk Standard, skal du klikke på "Send kommentar" for det aktuelle afsnit.. Hvis du ønsker at arbejde videre med dine kommentarer, skal du i stedet klikke på "Gem kommentar til senere redigering".

Du kan tilføje og ændre i gemte kommentarer, men hvis du sender kommentaren, kan du ikke vende tilbage for at redigere.

Hvis du har gemte kommentarer, som ikke er afsendt, vil du, før høringsperioden udløber, blive mindet om, at du har ikke-afsendte kommentarer.